Vehicles
223 not categorized PORSCHE 914 BACK ORDERCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.930123002X This remanufactured turbo is a direct replacement for original part # 930 123 002 00. The remanufacturing is completed in Germany by kkk/borg warner certified technicians. This ensures reliability, superior performance and cost effectiveness. The remanufacturing process includes: complete disassembly. All parts are cleaned, inspected and measured for tolerances. Turbine wheels are replaced. Thrust bearings are replaced. All new seals are installed. Internals are reconditioned. Parts are balanced (static & dynamic) according to balancing protocol. For a complete installation we recommend adding a gasket, part # 93012319105 an intake sleeve, part # 93011015801 and be sure to have a few spare studs on hand, part #...(choose a part on the right to read more)
From $2,981.74
Make a selection 930347010X If you are experiencing a tight steering feel, grinding noise when turning or leaking steering fluid check your steering rack. This is an exchange part that we source in Germany to ensure quality, reliability and precise fitment. This part is a remanufactured part, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and resell-able, the core deposit will be refunded. Exchange for original part # 930 347 010 00 View/Change Diagram
From $1,037.30
Make a selection 930602015AX This part is a remanufactured part, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and resell-able, the core deposit will be refunded. The remanufacturing process includes full inspection, disassembly, cleaning and degreasing. We then install a toothed timing belt, 3 German made top bearings, 1 German made lower bearing and a distributor pinion pin (part # 930 602 922 00). Clearances, timing and proper operation are then checked to ensure reliability. Please note: your core distributor must be sent in advan...(choose a part on the right to read more) View/Change Diagram
From $1,168.99
Make a selection 93060290401A Distributor caps are often overlooked as the source of ignition issues. If yours is failing or cracked, you can experience shaking at idle, poor starting in the cold, stalling and backfiring. Be sure to replace it if you see any signs of cracking. This is a high-quality beru replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
From $26.40
Make a selection 94463120201 Beautiful original foglight assembly for the passenger side of your 944 spoiler. comes complete with the wiring stub and the backing plate. an easy bolt in. Order two so they crystal clear like match. View/Change Diagram
$209.77
Make a selection 96410628309 This cover sits upright along the back of the motor nearest the fire wall on the right side. If you are removing the motor for maintenance, be sure to check and replace the engine covers / heat shields as necessary. We recommend replacing the grommet, part 99970212650 at the same time. Sold individually. 1 necessary per car. View/Change Diagram
From $347.60
Make a selection 96434703200 If your outer tie rods are worn you will experience sloppy steering response and knocking / creaking sounds. Your outer tie rods keep the steering centered, so failure can be very dangerous and can seriously affect steering control. Prevent that from happening by replacing them as quickly as possible with our genuine replacement inner tie rods. Once you do, you will experience tighter, more precise feedback without noise. Complete kit consists of: 1 qty. Tie rod 1 qty. Hexagon nut (m14 x 1.5) 1 qty. Ball joint end 1 qty. Lock nut & pin sold individually. Left or right side fitment. 2 qty. Required. Tech tip: replace the inner tie rods also for a new car steering feel ! Purchase our part # 96434705804 & 96434719...(choose a part on the right to read more) View/Change Diagram
From $55.29
Make a selection 964603156BX This part is a remanufactured part, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and resell-able, the core deposit will be refunded. Includes a new voltage regulator. Sold individually. 1 necessary per car. View/Change Diagram
From $425.58
Make a selection 964604104X This part is a remanufactured part, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and resell-able, the core deposit will be refunded. If your starter is on its way out, you will notice an intermittent clicking noise and a delay in the vehicle actually starting. Eventually you hear a metallic screeching noise that is a sure sign that your starters bendix mechanism, bearings or solenoid are kaput. When ordering a new starter be sure to check the rubber cap on the terminal for cracks which allows moisture in ...(choose a part on the right to read more) General Fitment911 1994-98911 1989-94
From $250.59
Make a selection F9764120002MTIP The differences are day… and night! Gauge faces are one of the most visible and frequently looked at components in your Porsche. Why skimp on quality? Gauge faces should have clearly visible markings and be easy to read with and without back lighting. Replacement faces should offer similar qualities, but many gauge faces on the market don't quite make the grade. FVD gauge faces are different. What makes them different you ask? See for yourself. In the below pictures you will see that the tiptronic is an FVD gauge face and the 6 speed gauge face is the competitions. The daytime difference (the competition): darker, more yellow appearance raised orange warning lights, not flush larger, bolder script than t...(choose a part on the right to read more)
$784.30
Make a selection F5864120007D The differences are day… and night! Gauge faces are one of the most visible and frequently looked at components in your Porsche. Why skimp on quality? Gauge faces should have clearly visible markings and be easy to read with and without back lighting. Replacement faces should offer similar qualities, but many gauge faces on the market don't quite make the grade. FVD gauge faces are different. What makes them different you ask? See for yourself. In the below pictures you will see that the tiptronic is an FVD gauge face and the 6 speed gauge face is the competitions. The daytime difference (the competition): darker, more yellow appearance raised orange warning lights, not flush larger, bolder script than t...(choose a part on the right to read more) General FitmentCAYENNE 2011-14
From $830.03
Make a selection 99660610599 If you are noticing engine vibrations, misfires and even backfiring your crankshaft position sensor maybe bad. Your car's dme (ecu) uses the signal from the crankshaft position sensor to control ignition timing and fuel injection, so if your sensor is failing your engine is suffering from poor timing and is not running efficiently. This kit is complete and ready to install.
$132.75
Make a selection 99660610500 If you are noticing engine vibrations, misfires and even backfiring your crankshaft position sensor maybe bad. Your car's dme (ecu) uses the signal from the crankshaft position sensor to control ignition timing and fuel injection, so if your sensor is failing your engine is suffering from poor timing and is not running efficiently. Please note: if ordering for the 996 turbo or GT2, this is only for manual transmissions. View/Change Diagram
From $85.89
Make a selection BAT005 Many pre. 1977 Porsche 911's are not equipped with factory oil plumbing (hard lines and thermostat). In this case fitting an oil cooler requires making a hose run from the rear to the front of the vehicle and back. We find the easiest and most cost effective method of plumbing is to duplicate the factory plumbing route using aeroquip hose and fittings with a mocal oil thermostat and oil cooler. The various kits that we offer to accomplish this task include; one of a number of oil cooler options (some are suitable for both fender or front spoiler location), mocal -12 an oil thermostat with mounting bracket, 30 foot length of aqp -12 an stainless braid 3/4" id hose, 30 mm metric to -12 an adaptors for the oil t...(choose a part on the right to read more) General Fitment911 1974-77911 1965-69 911 1970-73 928 1978-82
$1,090.00
Make a selection BES91105000S This muffler was specifically designed for a backdate to the st look. It is manufactured for mid-range and top end performance, all without drone inside the cabin. It seamlessly mates to ssi heat exchangers for added performance while keeping the cabin warm in the winter. The muffler is vastly different than the common baffle plated mufflers stuffed with packing material that are common in the aftermarket. Ours are uniquely made with double perforated sound absorption tubes based on the halbgegenstromprinzip (half counter current principle). The acoustic silencer absorption tubes are made in a trapezoidal pattern and are perforated with varying diameters, which isolate and dampen the unwanted frequencies that c...(choose a part on the right to read more)
$2,014.10
Make a selection BES99101260S - + 20 crank hp & + 14 crank torque. - 200 cell hjs tri-metallic "hd" cats. - 2 tubing (50 mm) with motorsport merge collector. - weighs 18.5 lbs. (8.4 kg). - 1.5 lb (9.1 kg) saving's over OEM header. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - works with OEM sealing rings and clamps. See below for part numbers. - made in Germany. - reduces thermal load and backpressure to for more torque in the mid-range and hp on the top end. Be sure to add new clamps and sealing rings to your order. 2 qty. Clamps are needed, they are part # 99711133690 and 2 qty. Sealing rings are needed, they are part # 98011156100. Our latest development for the GT3 is aimed at those who are looking fo...(choose a part on the right to read more)
$5,286.60
Make a selection BES99102240SHDO + 15 hp & + 14 torque - 200 cell high flow, tri metal German hjs "hd" high durability matrix sports catalysts. - can be used with FVD "brombacher" mufflers. - weighs 15.5 lbs. (7.0 kg). - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - made in Germany. - intoxicating growl at idle, partial throttle and wide open throttle. The catalytic converter cores used in this system are the most advanced in the industry. They are produced by hjs in Germany and are a 200 cpsi (cell per square inch) tri-metal design. Tri-metal cats are the freest flowing and environmentally friendly aftermarket cats produced today. Tri-metal catalytic converters are rodium, platinum and iridium coated and per...(choose a part on the right to read more)
$3,985.30
Make a selection BES99125010SK Are you one of those that are looking for more sound from your Porsche sport exhaust (pse)? Perhaps it's not quite as aggressive as you would like, or your last Porsche just sounded so much better? Don't worry, we have you covered, and the beauty is, you don't have to touch the catalytic converters which is a big no, no with Porsche dealers. With the valves open you receive a far more exotic, rich, deep, turbo motorsport tone and with the valves closed, soft subtle, completely stock sounds. So, absolutely no compromise and you will be thinking, the car really should have left the factory like this! Features: - + 10 crank hp & + 8 crank torque. - weighs 29 lbs. (13 kg) - German v2a - x5crni18-10 - 1.4301 stai...(choose a part on the right to read more)
$4,312.00
Make a selection BES99125020SK No need for Porsche sport exhaust (pse) envy with this muffler! This offers weight savings and a far more exotic sound than the pse, all without drone. It is the perfect compromise for you and your loved ones. Rich, deep, turbo motorsport tones with the valves open and soft subtle, completely stock sounds with them closed. Top of the line or range depending on the english and is the best choice for a daily driver. Features: - + 16 crank hp & + 15 crank torque. - weighs 37 lbs. (17 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - direct bolt on replacement for the factory center muffler. - includes necessary installation hardware. - reduces turbo lag, backpressure and thermal lo...(choose a part on the right to read more)
$4,651.90
Make a selection BES99125040S Perfect muffler for those looking for a more aggressive exhaust note without changing the factory catalytic converters. The added benefit is you can reuse your OEM catalytic converters for emissions purposes. + 25 hp & + 19 torque* - reuses OEM cats, perfect for those concerned about warranty. - open muffler design for added power. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - 4 on a scale of 1-10 in volume (1 being stock) below 3,000 rpms, 6 on a scale of 1-10 in volume under maximum load (3 being stock). - includes new clamps and muffler straps.* - made in Germany. - modular design for future 100 cell, 200 cell or cat bypass use. - more distinguished ...(choose a part on the right to read more)
$2,655.40
Make a selection BES99300240SOER For all 993 turbo and GT2 General Fitment911 1994-98
$9,235.60
Make a selection BES99602060S Catalytic by pass “x torque” design made by m&m in Germany. General Fitment911 GT3 2003-05
$1,564.20
Make a selection BES99602260S 200 cell catalytic “x torque” design made by m&m in Germany. General Fitment911 GT3 2003-05911 1998-05
$2,823.70
Make a selection BES99701260S1HD These headers and cats are perfect for those who want to run sport cats without a software program. Our latest development for the GT3 is aimed at those who are looking for more torque in the mid range, a rich, deep exhaust growl and most importantly no check engine light with stock software. General Fitment911 GT3 2007-11
From $4,184.06
Make a selection BES99709260T "brombacher" racing exhaust system for 997gt3/rs General Fitment911 GT3 2007-11
$11,661.10
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |